
Copper Strip plate sheet Upward Continuous Casting Machine Energy Saving
Technical parameters of production line
1. Production line process
Feeding, smelting, static, thermal insulation, crystallization,
traction, beating, sawing and cutting
2. Production line equipment
Two conjoined frequency cored induction furnace 1set
alloy copper lead mould 2set
four columns servo drive up lead machine 1set
Coiler with a core reel 2 sets
3. Main technical parameters of the production line equipment
3.1 Two connected frequency core induction furnace
The electric furnace:120KW holding+ 210KW melting
3.1.1 Main technical parameters of melting Department
(1) rated power: 210KW;
(2) rated voltage: 380V;
(3) frequency: 50HZ;
(4) melting rate: 750kg/h (+ +);
(5) rated capacity: 2.5t;
(6) Power consumption: less than 280kwh/t ;
(7) power factor: 0.95-1 (after compensation);
(8) the maximum temperature of the furnace: 1350.
3.1.2 Main technical parameters of holding Department
(1) rated power: 120KW;
(2) rated voltage: 380V;
(3) frequency: 50HZ;
(4) rated capacity: 3.5t;
(5) power factor: 0.95-1 (after compensation);
(6) the maximum temperature of the furnace: 1350.
3.2 copper alloy lead mould
Lead cast specification: wide 450mm * thickness 14mm * 2
3.3 four columns servo drive up machine
(1) servo motor power: 4.4KW;
(2) lead casting speed: 50-150mm/min
(3) lead casting method: Lead - stop - Lead - stop - withdrawal -
stop - lead two kinds of process parameters online adjustable;
(4) output: more than 10t;
3.4 Coiler with a core reel
(1) the thickness of roll material: 15mm max;
(2) roll width: 450mm;
(3) curl diameter: diameter of 500mm;
(4) curl weight: 8t max;
(5): Max with 2100mm curl diameter;
(6) motor power: 3kw;
(7) speed reducer ratio: 1003.
4.Main composition of the production line equipment
4.1 Two conjoined frequency cored induction furnace
The electric furnace is mainly composed of a furnace cover, a
furnace shell, an induction body, a support, an electric control
system, a temperature measuring system and a cooling system of the
equipment.
The furnace shell and the bottom bracket of the upper furnace body
are welded with the Q235 steel plate and the steel plate, and the
lower part of the smelting induction body and the heat insulation
induction body are connected with the upper furnace body through a
flange. Melting groove is made of red copper casting; core with
Japan Z10 silicon steel laminations loaded into; coil with double
glass ribbon wrapped rectangular copper winding and, good
insulation, strong cooling effect; water cooling jacket is made of
stainless steel plate 1Cr18ni9Ti thickness 3mm, it has high
strength, vibration magnetic effect good. The furnace chamber is
divided into three cavities, the melting chamber, the intermediate
excessive cavity, the thermal insulation cavity. Melting chamber of
material function; excessive cavity is mainly static copper water,
reducing smelting furnace material temperature fluctuation effect
of furnace temperature on the thermal insulation, heat preservation
cavity is mainly to give traction bar provide stable molten copper
and stable temperature.
Two conjoined frequency cored induction furnace control system,
melting and insulation department are used step self coupling
voltage regulating transformer to adjust the pressure, adjustable
pressure profile of 380V, 340v, 300V, 270V, 240V, 210v, 180V, 150V,
120V, 90V voltage (line). Melting, thermal insulation furnace
temperature control are equipped with manual and automatic
conversion switch, when the switch is in the manual, artificial
regulation of voltage knob for regulating the output voltage of a
transformer, so as to control the power output of the electric
furnace; when the switch is arranged in the automatic control
system by artificial intelligent temperature controller to adjust
the output voltage of the transformer pressure. An automatic
temperature control system is arranged in the heat insulating part
of the smelting part. The thermocouple is a horizontal inserting
type, and the heat insulating part is an inserting type.
4.2 copper alloy lead mould
The mold is made of one cooling and two cooling. The cooling jacket
is made of heat resistant steel, and the other parts are made of
cold rolled steel sheet. With water grooves in the mold on the
cooling water in the mold directional flow, so as to ensure the
uniformity of cooling.
Cooling water distribution system is specially designed for the
cooling of the mould. The system is provided with a water inlet
flow meter and a water outlet thermometer, which is convenient for
the user to monitor and adjust the water system. In order to ensure
the stability of the water supply of the crystallizer, the addition
of a crystallizer water temperature control system is composed of
plate condenser intelligent electric control valve, a temperature
controller, when there is a change in water temperature of mould,
temperature change signal transfer to the intelligent electric
control valve, the system sends signal to the intelligent electric
control valve, intelligent electric control valve according to the
given signal, automatic control the size of the water flow, of
plate condenser cooling intensity of automatic adjustment, so as to
ensure the stability of the water temperature of mould.
4.3 four column servo drive up lead machine
The upper guide machine is composed of four upright posts, an upper
and a lower moving screw rod, a servo power part, a power
transmission part, a pressing traction roller part and a process
operation system.
Four post bracket is composed of a hollow square pipe welding, the
up and down moving wire rod part is by motor, worm gear and worm
gear reducer, chain and wire rod is composed of a power
transmission system.
When the holding furnace copper water level change, through the
copper water level tracking detection system, transmits the signal
to the automatic control system of convey instructions to the
motor, motor according to the instructions on the mobile, and
copper water level changes also passes through the liquid level
tracking system will transmit the signal to feeding alarm system,
alarm alarms, suggesting that operator feeding.
The traction of the traction machine is composed of a servo motor,
a speed reducer, a gear system, a transmission shaft, a traction
roller and a pressing roller.
Process operation system mainly consists of anti interference of
operating platform, servo system, 10.5 inches color man-machine
interface, contactor and a button, controlled by PLC and
man-machine interface, the interface can display speed,
4.4 Coiler with a core reel
Composed of a frame, a power transmission system and a wire
collecting plate. Frame is welded by steel I-beam and drive
consists of a motor, a speed reducer, a transmission shaft
composition; speed by frequency modulator for motor frequency
change to control motor speed.
The take-up disk comprises a disk body and swelling mechanism. When
the strip a roll, by the expansion mechanism of the contraction
will strip out.
5. Scope of production line supply
NO. | NAME | QUANTITY |
1 | 750kg/500kg electrical cabinets | each 1 set |
2 | Upward automatic control cabinet | 1set |
3 | Four columns servo drive up machine | 1set |
4 | Roller | 2pcs |
5 | Roller tube | 12pcs |
6 | 750kg/500kg iron core | each 1 set |
7 | 750kg/500kg water jacket | each 1 set |
8 | 750kg/500kg coil | each 1 set |
9 | 750kg/500kg copper channel | each 1 set |
10 | alloy copper lead mould assembly | 2sets |
11 | graphite mould | 4pcs |
12 | coiler with a core reel | 2sets |
13 | two connected induction furnace body | 1set |
14 | S graduated thermocouple | 2pcs |
15 | Thermocouple protective sleeve | 2pcs |
16 | Silicon carbide protective sleeve | 4pcs |
17 | Up lead head | 2sets |
18 | Quick connector | 10pcs |
19 | Quartz sand | 7tons |
20 | Refractory bricks | 1set |
21 | Plate-type condenser | 1set |
22 | Intelligent electric control valve | 1set |
6.Production line of technical information to provide
(1) the production line of civil conditions;
(2) electrical control chart;
(3) spare parts drawing;
(4) instruction manual;
Wuxi East China Furnace Co.,Ltd
Welcome to visit and inspect!
Contact person: Joey Wong
Tel: +86 510 83788308
Fax: +86 510 83786308
Mob: +86 139 2112 5611
Wechat: 86 139 2112 5611
Whatsapp: 86 139 2112 5611
email:Joey@wxhddl.cn
Joe.777@outlook.com
Wuxi Huadong Industrial Electrical Furnace Co.,Ltd.
Our company is located at the northeast of Wuxi, Jiangsu Province, with only 2.5 hours of driving distance to Shanghai Pudong International Airport, and the traffic is very convenient.
Wuxi Huadong Industrial Furnace Co., Ltd is a comprehensive enterprise integrating scientific research & development, engineering designing, system integration, equipment installation and sales & services. Our company is dedicated to professional manufacture the production lines for casting of various non-ferrous metals and heat treatment since 1989.
The production lines for casting non-ferrous metals supplied by our company is complete in categories, specifications and types, mainly capable of casting metals including copper and copper alloys, also related to non-ferrous metals such as magnesium, aluminum and zinc etc. The casting modes include horizontal continuous casting, vertical casting and upward casting; By using our production lines, customers can get billet products with sections of near-the-net-shape dimensions and shapes, including 8 major categories i.e. plates, strips, rods, foils, tubes, bars and shapes. Heat treatment equipments include multiple types of electric resistance furnaces or combination, such as well type, box type, bogie-hearth type, bell type, protective-atmosphere type, vacuum bright type, strong-convection circulation type etc. For casting production lines and heat-treatment equipments, our company can also provide various types of spare parts (furnace shells, melting grooves, water jackets, iron cores, crystallizers, special refractory, temperature measurement devices, transformers, reactors, electric resistance heating elements, and mechanical parts etc.); Our company can also provide cold-processing equipments such as drawing mills and cold-rolling mills for tubes, rods and shapes, as well as scrap metal balers etc.
Our company can develop, design, and manufacture equipments for specific production lines according to customers' requirements, provide complete services of solutions; Committed to quality, quality priority covers the whole process of designing, purchasing ,manufacturing, production, installation and after-sales services etc. We are doing our best to realized most advanced in technology, most reasonable in configuration, most superior in quality, and most inexpensive in cost. We strictly follow the requirements of ISO9000 quality system, achieving first-class product quality.
Choosing Wuxi Huadong Electric Industrial Furnace Co. ,Ltd as the
partner means choosing trust and guarantee, and the correction
choice is the safeguard for the smooth operation of your
undertakings and reliable return of your investment.
Wuxi East China Furnace Co. ,Ltd would like to
cordially welcome friends from home and abroad for visiting and
guidance.